The number of items in your shopping list has exceeded the maximum limit. Please remove some items, or create a new shopping list.
Oops. This product is only available in a minimum quantity of or more units
Roll over image to zoom in

Gorilla Epoxy Glue

Product Description

Incredibly strong. Sets in 5 min. For the toughest jobs on Planet Earth. Color: Dries clear. Bonded Strength: 3000 PSI. Indoor/Outdoor: Water resistant. Structural gap filler. Bonds: metal, wood, ceramic, glass, most plastic and more! Includes: Resealable cap, stir stick & mixing tray. Incredibly strong and fast setting. Easy, even dispensing. Low odor. Solvent resistant and non-toxic once cured. Made in USA.

Preparation Instructions

All surfaces should be clean, dry, and free of grease and oil. To improve adhesion, roughen smooth surfaces with sandpaper before gluing. 1. Protect work area from spills. 2. Remove black cap from plunger. With tip pointing upward, cut or snap end from tip of syringe. With tip still upward, eliminate air and ensure even dispensing by slowly pushing plunger until resin and hardener are at the tip. 3. Dispense even amounts of resin and hardener onto a clean, disposable surface. The package blister can be used as a mixing tray. 4. Mix until color is uniform. 5. Apply to surface within 5 minutes. Bond strength will decrease the longer you wait to apply. 6. Clamp surfaces together or leave undisturbed for 30 minutes. 7. To close, pull plunger slightly back. Wipe syringe tip clean, dry cloth. Align notch on tip with slot on black cap. You will hear a snap when black cap is closed tightly. Heat or sun exposure can cause product to yellow. Not recommended for use on polyethylene or polypropylene plastics. Not recommended for continuous submersion or below-waterline use. Set Time: 5 minutes to apply and position. Handling Time: 30 minutes undisturbed. Cure Time: 100% in 24 hours for load bearing weight. Application in cooler temperatures may cause longer cure times. Temp. Range: Bond withstands - 10 degrees F to 180 degrees F. Cured Color: Dries clear. Storage: After use, clean syringe and replace black cap. Store in a cool, dry place. Clean-up: Remove excess glue immediately from project surface with dry cloth and acetone, mineral spirits or rubbing alcohol. See below for removal from skin.

Safety Warning
Corrosive, irritant and sensitizer. Keep out of reach of children and animals. contains epoxy resin, polymercaptan and amine curing agents. Can cause eye and skin burns and respiratory tract irritation. may cause allergic skin reaction. May be harmful if absorbed through skin or if swallowed. Can enter lungs and cause damage. Do not breathe vapors. Do not ingest. do not get in eyes or on skin or clothing. Use in a well-ventilated area, and keep container tightly closed until ready for use. For eye contact, wash with water for 15 min., and seek immediate medical attention. For skin contact, wash with soap and water. If irritation and symptoms persist, seek medical attention. If ingested, do not induce vomiting, and seek immediate medical attention. For medical emergencies only, call 1-800-420-7186.
Actual product packaging and materials may contain more or different information than that shown on our website. You should not rely solely on the information presented here. Always read labels, warnings and directions before using or consuming a product. View full Product Information Disclaimer


Tell us what you think!
Tell us what you think!
Be the first to write a review!
Wondering what to say?
  • Include usage tips, key benefits, and helpful suggestions.
  • Did you have a good or bad experience?
  • Would you recommend this to friends or family?
  • Be respectful to others.
{{review.commentTitle}} {{review.timestampFormatted}}
by {{review.sender.screenName}} {{review.sender.screenName ? review.sender.screenName : 'Anonymous'}}
Was this review helpful to you? Yes {{review.posVotes}} No {{review.negVotes}} Flag
Customer Relations